Hybrid Computational Techniques: Electromagnetic Propagation Analysis in Complex Indoor Environments
In: IEEE antennas & propagation magazine, Band 61, Heft 6, S. 20-30
ISSN: 1558-4143
14 Ergebnisse
Sortierung:
In: IEEE antennas & propagation magazine, Band 61, Heft 6, S. 20-30
ISSN: 1558-4143
In: IEEE antennas & propagation magazine, Band 56, Heft 4, S. 232-245
ISSN: 1558-4143
In: IEEE antennas & propagation magazine, Band 55, Heft 6, S. 240-258
ISSN: 1558-4143
In this article, a compact coplanar waveguide (CPW) technique based ultra-wideband multipleinput- multiple-output (MIMO) antenna is proposed. The design is characterized by a broad impedance bandwidth starting from 3 GHz to 11 GHz. The overall size of the MIMO design is 60 x 60 mm2 (1.24 x 1.24 g2 g @ 3 GHz) with a thickness of 1.6 mm. To make the design ultra-wideband, the proposed MIMO antenna design has four jug-shaped radiating elements. The design is printed on a FR-4 substrate (relative permittivity of er = D 4:4 and loss tangent of tand D 0:025). The polarization diversity phenomenon is realized by placing four antenna elements orthogonally. This arrangement increases the isolation among the MIMO antenna elements. The simulated results of the ultra-wideband MIMO antenna are verified by measured results. The proposed MIMO antenna has a measured diversity gain greater than 9.98, envelope correlation coefficient (ECC) less than 0.02, and good MIMO performance where the isolation is more than -20dB between the elements. The group delay, channel capacity loss (CCL), and the total active reflection coefficient (TARC) multiplexing efsiciency and mean effective gain results are also analyzed. The group delay is found to be less than 1.2ns, CCL values calculated to be less than 0.4 bits/sec/Hz, while the TARC is below -10dB for the whole operating spectrum. The proposed design is a perfect candidate for ultrawideband wireless communication systems and portable devices. ; This work was supported in part by the Universidad Carlos III de Madrid and the European Union's Horizon 2020 Research and Innovation Program under the Marie Sklodowska-Curie Grant 801538, and in part by the Ministerio de Ciencia, Innovaciôn y Universidades, Gobierno de España (MCIU/AEI/FEDER, UE) under Grant RTI2018-095499-B-C31.
BASE
The upcoming design and implementation of the new generation of 5G cellular systems, jointly with the multiple wireless communication systems that nowadays coexist within vehicular environments, leads to Heterogeneous Network challenging urban scenarios. In this framework, user's Radiofrequency Electromagnetic Fields (RF-EMF) radiation exposure assessment is pivotal, to verify compliance with current legislation thresholds. In this work, an in-depth study of the E-field characterization of the personal mobile communications within urban public trams is presented, considering different cellular technologies (from 2G to 5G). Specifically, frequency bands in the range of 5G NR frequency range 1 (FR1) and millimeter wave (mm-wave) bands within frequency range 2 (FR2) have been analyzed for 5G scenarios, considering their dispersive material properties. A simulation approach is presented to assess user mobile phone base station up-link radiation exposure, considering all the significant features of urban transportation trams in terms of structure morphology and topology or the materials employed. In addition, different user densities have been considered at different frequency bands, from 2G to 5G (FR1 and FR2), by means of an in-house developed deterministic 3D Ray-Launching (3D-RL) technique in order to provide clear insight spatial E-field distribution, including the impact in the use of directive antennas and beamforming techniques, within realistic operation conditions. Discussion in relation with current exposure limits have been presented, showing that for all cases, E-Field results are far below the maximum reference levels established by the ICNIRP guidelines. By means of a complete E-field campaign of measurements, performed with both, a personal exposimeter (PEM) and a spectrum analyzer within a real tram wagon car, the proposed methodology has been validated showing good agreement with the experimental measurements. In consequence, a simulation-based analysis. ; This work was supported in part by the School of Engineering and Sciences, Tecnologico de Monterrey, in part by the Ministerio deCiencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER,UE) under Grant RTI2018-095499-B-C31, in part by theMinistry of Science and Higher Education/National Centre for Research and Development and the Ministry of Family, Labour, and SocialPolicy, through the Poland National Programme Improvement of Safety and Working Conditions, and in part by Sub-Directorate-Generalfor Research Assessment and Promotion, Spain, under Project PI14CIII/00056 ; Sí
BASE
We're living in a world where information processing isn't confined to desktop computers-it's being integrated into everyday objects and activities. Pervasive computation is human centered: it permeates our physical world, helping us achieve goals and fulfill our needs with minimum effort by exploiting natural interaction styles. Remote interaction with screen displays requires a sensor-based, multimodal, touchless approach. For example, by processing user hand gestures, this paradigm removes constraints requiring physical contact and permits natural interaction with tangible digital information. Such touchless interaction can be multimodal, exploiting the visual, auditory, and olfactory senses. ; Acknowledgments This study received funding from Universidad Carlos III de Madrid and the European Union's Horizon 2020 Research and Innovation Programme under Marie Sklodowska-Curie grant 801538. *is study was also partially supported by Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER, UE) (RTI2018- 095499-B-C31). Additionally, the authors sincerely appreciate funding from Researchers Supporting Project (RSP- 2021/58), King Saud University, Riyadh, Saudi Arabia.
BASE
This paper presents a unique concentric hexagonal-shaped ring antenna for radio frequency identification (RFID) tags. The rings are excited with a common microstrip feedline. The radiation characteristics of the antenna is improved by locating a horizontal a parasitic element in the vicinity of the hexagonal-shaped rings. The proposed antenna was used in the implementation of a 3×1 antenna array. The impedance match of the 3×1 RFID tag was enhanced by incorporating a T-shaped stub. The antenna is designed to operate at the UHF band from 800 MHz to 960 MHz. It was implemented on FR-4 substrate with dielectric constant and thickness of 4.3 and 1.6 mm, respectively. The size of the RFID tag antenna is 36×10 mm 2 . Its impedance was matched to Alien Higgs RFIC chip of impedance 10 – j 82.5 Ω at 895 MHz. Measured results show the proposed RFID tag antenna provides an impedance bandwidth, maximum gain and radiation efficiency of 160 MHz, 2 dBi, and 66.5%, respectively. With effective isotropic radiated power (EIRP) limited to 36 dBm to comply with FCC regulations for UHF band RFIDs it radiates in the broadside direction over a range of 9 m making it desirable for various applications including supply chain management, logistic control, and vehicle identification. ; This project has received funding from Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation program under the Marie Sklodowska-Curie Grant 801538. Also, this work is partially supported by RTI2018-095499-B-C31, Funded by Ministerio de Ciencia,Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER,UE). Additionally, it received funding from the Researchers Supporting Project number (RSP-2021/58), King Saud University, Riyadh, Saudi Arabia.
BASE
The densification of multiple wireless communication systems that coexist nowadays, as well as the 5G new generation cellular systems advent towards the millimeter wave (mmWave) frequency range, give rise to complex context-aware scenarios with high-node density heterogeneous networks. In this work, a radiofrequency electromagnetic field (RF-EMF) exposure assessment from an empirical and modeling approach for a large, complex indoor setting with high node density and traffic is presented. For that purpose, an intensive and comprehensive in-depth RF-EMF E-field characterization study is provided in a public library study case, considering dense personal mobile communications (5G FR2 @28 GHz) and wireless 802.11ay (@60 GHz) data access services on the mmWave frequency range. By means of an enhanced in-house deterministic 3D ray launching (3D-RL) simulation tool for RF-EMF exposure assessment, different complex heterogenous scenarios of high complexity are assessed in realistic operation conditions, considering different user distributions and densities. The use of directive antennas and MIMO beamforming techniques, as well as all the corresponding features in terms of radio wave propagation, such as the body shielding effect, dispersive material properties of obstacles, the impact of the distribution of scatterers and the associated electromagnetic propagation phenomena, are considered for simulation. Discussion regarding the contribution and impact of the coexistence of multiple heterogeneous networks and services is presented, verifying compliance with the current established international regulation limits with exposure levels far below the aforementioned limits. Finally, the proposed simulation technique is validated with a complete empirical campaign of measurements, showing good agreement. In consequence, the obtained datasets and simulation estimations, along with the proposed RF-EMF simulation tool, could be a reference approach for the design, deployment and exposure assessment of the current and future wireless communication technologies on the mmWave spectrum, where massive high-node density heterogeneous networks are expected. ; Project RTI2018-095499-B-C31 was funded by the Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER, UE). This project received funding from Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme under Marie Sklodowska-Curie Grant 801538.
BASE
This paper presents a metasurface based multiple-input multiple-output (MIMO) antenna with a wideband operation for millimeter-wave 5G communication systems. The antenna system consists of four elements placed with a 90 degree shift in order to achieve a compact MIMO system while a 2×2 non-uniform metasurface (total four elements) is placed at the back of the MIMO configuration to improve the radiation characteristics of it. The overall size of the MIMO antenna is 24×24 mm 2 while the operational bandwidth of the proposed antenna system ranges from 23.5-29.4 GHz. The peak gain achieved by the proposed MIMO antenna is almost 7dB which is further improved up to 10.44 dB by employing a 2×2 metasurface. The total efficiency is also observed more than 80% across the operating band. Apart from this, the MIMO performance metrics such as envelope correlation coefficient (ECC), diversity gain (DG), and channel capacity loss (CCL) are analyzed which demonstrate good characteristics. All the simulations of the proposed design are carried out in computer simulation technology (CST) software, and measured results reveal good agreement with the simulated one which make it a potential contender for the upcoming 5G communication systems. ; This work was supported in part by the Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant Agreement No 801538, and in part by the the Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER,UE) under Grant RTI2018-095499-B-C31.
BASE
In this article, a compact printed monopole dual-band antenna using artificial magnetic conductor (AMC)-plane with improved gain and broader bandwidth, applicable for off-body internet of things (IoT) devices is presented. The monopole antenna consists of two C-shaped resonators connected through a U-shaped monopole, parasitic elements, discrete ground circular rings and a co-planar waveguide (CPW) feedline. Each artificial magnetic conductor (AMC) unit cell consists of a slotted circular and a square stubs, designed with two zero-crossing phases for improving the radiation characteristics and to achieve the high gain. The overall size of the proposed AMC-backed antenna is 44.4 mm ×44.4 mm ×1.6 mm with electrical dimensions of 0.75lambdag×0.75lambdag×0.027lambdag . This AMC-backed antenna featured measured bandwidths of 9.6% and 12.4% with improved measured gain values of 4.88 dB and 4.73 dB at 2.45 GHz and 5.8 GHz, respectively. The specific absorption rate (SAR) values are analysed and found to be 1.58 W/kg at 2.45 GHz and 0.9 W/kg at 5.8 GHz. Therefore, the proposed AMC-backed antenna is useful for off-body IoT devices operating at 2.45 and 5.8 GHz industrial, scientific, and medical (ISM) band applications. ; This work was supported in part by the Universidad Carlos III de Madrid; in part by the European Union's Horizon 2020 Research and Innovation Programme under Marie Sklodowska-Curie Grant 801538; in part by the Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER and UE) under Grant RTI2018-095499-B-C31; and in part by the Researchers Supporting Project, King Saud University, Riyadh, Saudi Arabia, under Project number RSP-2021/58.
BASE
[Abstract] The development of multiple cultural and social related activities, such as shows related with the performing arts, conferences or presentations rely on facilities such as auditoriums, theatres and conference sites, which are progressively including multiple technological features in order to enhance user experience. There are still however situations in which user experience is limited owing to lack of environment adaption, such as people with disabilities. In this sense, the adoption of Context Aware paradigms within auditoriums can provide adequate functionalities in order to comply with specific needs. This work is aimed at demonstrating the feasibility in enhancing user experience (e.g., improving the autonomy of disabled people) within auditorium and theatre environments, by means of an Augmented Reality (AR) device (HoloLens smart glasses) with wireless system integration. To carry out the demonstration, different elements to build AR applications are described and tested. First, an intensive measurement campaign was performed in a real auditorium in the city of Pamplona (Baluarte Congress Center) in order to evaluate the feasibility of using Wi-Fi enabled AR devices in a complex wireless propagation scenario. The results show that these environments exhibit high levels of interference, owing to the co-existence and non-coordinated operation of multiple wireless communication systems, such as on site and temporary Wi-Fi access points, wireless microphones or communications systems used by performers, staff and users. Deterministic wireless channel estimation based in volumetric 3D Ray Launching have been obtained for the complete scenario volume, in order to assess quality of service metrics. For illustration purposes, a user-friendly application to help hearing impaired people was developed and its main features were tested in the auditorium. Such an application provides users with a 3D virtual space to visualize useful multimedia content like subtitles or additional information about the show, as well as an integrated call button. ; 10.13039/501100010801-Article Processing Charges (APC) from the Xunta de Galicia (Grant Number: ED431G 2019/01) 10.13039/501100011033-Agencia Estatal de Investigación of Spain (Grant Number: TEC2016-75067-C4-1-R, RED2018-102668-T and PID2019-104958RB-C42) 10.13039/501100008530-European Regional Development Fund (ERDF) of the European Union (EU) [Agencia Estatal de Investigación (AEI)/Fondo Europeo de Desarrollo Regional (FEDER), UE] 10.13039/100014440-Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER,UE) (Grant Number: RTI2018-095499-B-C31) ; Xunta de Galicia; ED431G 2019/01
BASE
Circular polarized (CP) antennas are well suited for long-distance transmission attainment. In order to be adaptable for beyond 5G communication, a detailed and systematic investigation of their important conventional features is required for expected enhancements. The existing designs employing millimeter wave, microwave, and ultra-wideband (UWB) frequencies form the elementary platform for future studies. The 3.4–3.8 GHz frequency band has been identified as a worthy candidate for 5G communications because of spectrum availability. This band comes under UWB frequencies (3.1–10.6 GHz). In this survey, a review of CP antennas in the selected areas to improve the understanding of early-stage researchers specially experienced antenna designers has presented for the first time as best of our knowledge. Design implementations involving size, axial ratio, efficiency, and gain improvements are covered in detail. Besides that, various design approaches to realize CP antennas including (a) printed CP antennas based on parasitic or slotted elements, (b) dielectric resonator CP antennas, (c) reconfigurable CP antennas, (d) substrate integrated waveguide CP antennas, (e) fractal CP antennas, (f) hybrid techniques CP antennas, and (g) 3D printing CP antennas with single and multiple feeding structures have investigated and analyzed. The aim of this work is to provide necessary guidance for the selection of CP antenna geometries in terms of the required dimensions, available bandwidth, gain, and useful materials for the integration and realization in future communication systems. ; This project has received funding from Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation program under the Marie Sklodowska-Curie Grant 801538. Also, this work was partially supported by RTI2018-095499-B-C31, Funded by Ministerio de Ciencia,Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER,UE).
BASE
In this paper, we present an analytical study for the investigation of the effects of the magnetoelectric elements of a reciprocal and nonreciprocal bianisotropic grounded substrate on the input impedance, resonant length of a dipole antenna as well as on the mutual coupling between two element printed dipole array in three configuration geometries: broadside, collinear and echelon printed on the same material. This study examines also the effect of the considered bianisotropic medium on the electric and magnetic field distributions that has been less addressed in the literature for antenna structures. Computations are based on the numerical resolution, using the spectral method of moments, of the integral equation developed through the mathematical derivation of the appropriate spectral Green"s functions of the studied dipole configuration. Original results, for chiral, achiral, Tellegen and general bi-anisotropic media cases, are obtained and discussed with the electric and magnetic field distributions for a better understanding and interpretation. These interesting results can serve as a stepping stone for further works to attract more attention to the reciprocal and non-reciprocal Tellgen media in-depth studies. ; This work is funded in part by: La Direction Générale de la Recherche Scientifique et du Développement Technologique (DGRSDT), Ministry of Higher Education and Scientific Research, Algeria, RTI2018-095499-B-C31, Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie Grant 801538, Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER, UE). Besides above, this work is also supported by the FCT/MEC through national funds and when applicable co-financed by the ERDF, under the PT2020 Partnership Agreement under the UID/EEA/50008/2019 project. This work is part of the POSITION-II project funded by the ECSEL joint Undertaking under Grant Number Ecsel-7831132-Postitio-II-2017-IA, www. posit ...
BASE
In this communication, a novel dual-polarized highly folded self-grounded Bowtie antenna that is excited through I-shaped slots is proposed for applications in sub-6 GHz 5G multiple-input-multipleoutput (MIMO) antenna systems. The antenna consists of two pairs of folded radiation petals whose base is embedded in a double layer of FR-4 substrate with a common ground-plane which is sandwiched between the two substrate layers. The ground-plane is defected with two I-shaped slots located under the radiation elements. Each pair of radiation elements are excited through a microstrip line on the top layer with RF signal that is 180º out of phase with respect to each other. The RF signal is coupled to the pair of feedlines on the top layer through the I-shaped slots from the two microstrip feedlines on the underside of the second substrate. The proposed feed mechanism gets rid of the otherwise bulky balun. The Bowtie antenna is a compact solution with dimensions of 32 × 32 × 33.8 mm3.Measured results have verified that the antenna operates over a frequency range of 3.1–5 GHz and exhibits an average gain and antenna efficiency in the vertical and horizontal polarizations of 7.5 dBi and 82.6%, respectively. ; This project has received funding in part by the Universidad Carlos III de Madrid and the European Union's Horizon 2020 Research and Innovation Programme under the Marie Sklodowska-Curie Grant 801538, in part by the Ministerio de Ciencia, Innovación y Universidades, Gobierno de Spain (MCIU/AEI/FEDER, UE) under Grant RTI2018-095499- B-C31, in part by the Innovation Program under Grant H2020-MSCA-ITN- 2016 SECRET-722424, and in part by the U.K. Engineering and Physical Sciences Research Council (EPSRC) under Grant EP/E022936/1.
BASE