In this work, the fabrication and properties of a Ge-based Kesterite Cu2ZnGeSe4 solar cell have been discussed. The substitution and the existence of the quaternary compound has been verified by physical methods. The device has a power conversion efficiency of 5.5% under AM1.5G illumination which is among the highest reported for pure Ge substitution. In depth electrical and optical analysis show that the Cu2ZnGeSe4 absorber has less bulk defects, less or no band tailing and no sub band gap emissions, which are all characteristic of Cu2ZnGeSe4 devices. These beneficial opto-electronic properties also result in a high open circuit voltage (V-oc) of 744 mV which is amongst the highest reported for Kesterite materials. ; Flemish government, Department Economy, Science and Innovation; European Union's Horizon 2020 research and innovation program [640868]
A study of the electronic conduction mechanisms and electrically active defects in polycrystalline Sb2Se3 is presented. It is shown that for temperatures above 200 K, the electrical transport is dominated by thermal emission of free holes, ionized from shallow acceptors, over the intergrain potential barriers. In this temperature range, the temperature dependence of the mobility of holes, limited by the intergrain potential barriers, is the main contributor to the observed thermal activation energy of the conductivity of 485 meV. However, at lower temperatures, nearest-neighbor and Mott variable range hopping transport in the bulk of the grains turn into the dominant conduction mechanisms. Important parameters of the electronic structure of the Sb2Se3 thin film such as the average intergrain potential barrier height ϕ = 391 meV, the intergrain trap density Nt = 3.4 × 1011 cm−2, the shallow acceptor ionization energy EA0 = 124 meV, the acceptor density NA = 1 × 1017 cm−3, the net donor density ND = 8.3 × 1016 cm−3, and the compensation ratio k = 0, 79 were determined from the analysis of these measurements. ; P. M. P. Salomé acknowledges the funding of Fundação para Ciencêa e Tecnologia (FCT) through the project IF/00133/ ̂2015. This research is supported by the Development of novel ultrathin solar cell architectures for low-light, low-cost, and flexible optoelectronic devices project (028075) co-funded by FCT and ERDF through COMPETE2020. B. Vermang has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program (grant agreement no. 715027). A. Shongalova acknowledges the funding of Erasmus + program 2016/17. This work was funded by FEDER funds through the COMPETE 2020 Programme and by FCTPortuguese Foundation for Science and Technology under the projects UID/CTM/50025/2013. The financial support from Brazilian funding agencies CNPq, CAPES, and FAPEMIG is also acknowledged. ; info:eu-repo/semantics/publishedVersion
This paper provides an overview of the physical vapor technologies used to synthesize Cu2ZnSn(S,Se)4 thin films as absorber layers for photovoltaic applications. Through the years, CZT(S,Se) thin films have been fabricated using sequential stacking or co-sputtering of precursors as well as using sequential or co-evaporation of elemental sources, leading to high-efficient solar cells. In addition, pulsed laser deposition of composite targets and monograin growth by the molten salt method were developed as alternative methods for kesterite layers deposition. This review presents the growing increase of the kesterite-based solar cell efficiencies achieved over the recent years. A historical description of the main issues limiting this efficiency and of the experimental pathways designed to prevent or limit these issues is provided and discussed as well. Afinal section is dedicated to the description of promising process steps aiming at further improvements of solar cell efficiency, such as alkali doping and bandgap grading ; 1. R Caballero and M León acknowledge financial support via the Spanish Ministry of Science, Innovation and Universities project (WINCOST, ENE2016-80788-C5-2-R) and thank H2020 EU Programme under the project INFINITE-CELL (H2020-MSCA-RISE-2017-777968). 2. S Canulescu and J Schou acknowledge the support from Innovation Fund Denmark. 3. D-H Kim acknowledges financial support via the DGIST R&D Program of the Ministry of Science and ICT, KOREA (18-BD-05). 4.C. Malerba acknowledges the support from the Italian Ministry of Economic development in the framework of the Operating Agreement with ENEA for the Research on the Electric System. 5.A Redinger acknowledges financial support via the FNR Attract program, Project : SUNSPOT, Nr.11244141. 6. E Saucedo thanks H2020 EU Programme under the projects STARCELL (H2020-NMBP-03-2016-720907) and INFINITE-CELL (H2020-MSCA-RISE-2017-777968), the Spanish Ministry of Science, Innovation and Universities for the IGNITE project (ENE2017-87671-C3-1-R), and the European Regional Development Funds (ERDF, FEDER Programa Competitivitat de Catalunya 2007–2013). IREC belong to the SEMS (Solar Energy Materials and Systems) Consolidated Research Group of the 'Generalitat de Catalunya' (Ref. 2017 SGR 862). 7. Taltech acknowledges financial support via the Estonian Ministry of Education and Research funding project IUT19-28 and the European Union Regional Development Fund, Project TK141. 8. B Vermang has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 Research and Innovation Programme (Grant Agreement No 715027)