Suchergebnisse

The present work evaluates the feasibility to capture at least 85% of the CO2 emitted by an advanced supercritical pulverized coal power plant of 800 MWe, delivering a CO2 product with a purity of 95% (dry basis) or higher, using an adsorption-based postcombustion capture process based on carbon honeycomb monoliths regenerated by steam stripping. Process performance has been evaluated through the dynamic simulation of the cyclic adsorption process. The fixed bed adsorption model, which was validated against experimental results, is based on the mass, momentum, and energy conservation equations, and it accounts for competitive adsorption between the three main flue gas components: N2, CO2, and H2O. The evaluated TSA process meets the targets for the capture rate and product purity, with a heat duty of 3.59 MJ kg–1 CO2, which is close to the specific reboiler duty of the benchmark amine-based absorption process. Materials and process development will lead to lower duties. A sensitivity analysis was carried out, and it has shown that slightly faster adsorption kinetics for CO2 could drop the specific heat duty of the process to 2.89 MJ kg–1 CO2, which is lower than that of the benchmark technology. From the process point of view, the use of waste heat from the power plant could further reduce the energy penalty of the integrated CO2 capture process. ; Work carried out with financial support from the HiPerCap Project of the European Union 7th Framework Programme (FP7) (2007−2013; Grant Agreement No. 608555) ; We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI). ; Peer reviewed

The EU FP7-funded HiPerCap project aims to develop novel post-combustion CO2 capture technologies and processes which are environmentally benign and have high potential to lead to breakthroughs in energy consumption and overall cost. Three different separation technologies are being evaluated on a fair basis: absorption, membranes and adsorption. In this work, some of the results related to the development of adsorption-based fixed bed systems are presented. The design and optimization of a multibed adsorption-based separation process requires the use of powerful simulators that can describe the non-steady state process. However, prior to use a mathematical model for process design this should be validated against experimental data. A VTSA experiment has been carried out in order to provide information on the cyclic performance of a microporous biochar. The working capacity of the adsorbent is reduced due to incomplete regeneration during cyclic operation, although it stabilizes at 0.5 mol CO2 kg-1 and 0.4 mol H2O kg-1 once cyclic steady state is reached. A non-isothermal non-adiabatic dynamic model of the VTSA cycle was built in Aspen Adsorption, which makes use of the Ideal Adsorbed Solution theory to account for competitive adsorption between N2, CO2 and H2O. The model satisfactorily describes the history of the temperature of the adsorbent, the pressure, the total mass flow rate of the effluent, and the working capacity at cyclic steady state of the VTSA experiment. The validated model will be used as a starting point for process development. ; Work carried out with financial support from the HiPerCap Project of the European Union 7th Framework Programme (FP7) (2007-2013; Grant Agreement No. 608555). ; Peer reviewed

The effect of post-treatment upon the H2O adsorption performance of biomass-based carbons was studied under post-combustion CO2 capture conditions. Oxygen surface functionalities were partially replaced through heat treatment, acid washing, and wet impregnation with amines. The surface chemistry of the final carbon is strongly affected by the type of post-treatment: acid treatment introduces a greater amount of oxygen whereas it is substantially reduced after thermal treatment. The porous texture of the carbons is also influenced by post-treatment: the wider pore volume is somewhat reduced, while narrow microporosity remains unaltered only after acid treatment. Despite heat treatment leading to a reduction in the number of oxygen surface groups, water vapor adsorption was enhanced in the higher pressure range. On the other hand acid treatment and wet impregnation with amines reduce the total water vapor uptake thus being more suitable for post-combustion CO2 capture applications. ; This work was carried out with financial support from the HiPerCap Project of the European Union 7th Framework Programme FP7 (2007–2013; Grant Agreement Number: 60855) and from the Gobierno del Principado de Asturias (PCTI-GRUPIN14-079). N.Q. acknowledges a fellowship from the Gobierno del Principado de Asturias (Programa Severo Ochoa). ; We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI). ; Peer reviewed

The main drawbacks of developing carbon adsorbents from pine sawdust, an abundant biomass feedstock, are the low carbon yield of the process and the poor mechanical properties of the resulting carbons. In an attempt to overcome these limitations, the effect of the addition of coal tar pitch was assessed. Adsorbent pellets were produced from pine sawdust and coal tar pitch by activation with CO2. The preparation process was optimized by using as decision variables the carbon yield and the adsorption performance of the adsorbents in conditions representative of post-combustion capture applications (10% CO2 at atmospheric pressure and at 50 °C). Subjecting the composite pellets to a pre-oxidation treatment with air increased the carbon yield of the production process, and also improved the adsorption kinetics and capacity of the final adsorbents. The prepared adsorbents present a high carbon yield, a superior mechanical resistance and a competitive adsorption performance. ; This work was carried out with financial support from the Spanish MINECO (Project ENE2011-23467), co-financed by the European Regional Development Fund (ERDF). M.G.P. acknowledges funding from the CSIC (JAE-Doc program), co-financed by the European Social Fund, and I.D. acknowledges funding from the Government of the Principado de Asturias. The authors are grateful to Industrial Química del Nalón S.A. for supplying the coal tar pitch sample. ; Peer reviewed

This work is the result of the collaboration between INCAR-CSIC (Spain) and CSIRO Energy (Australia) in the framework of the European Commission FP7 project HiPerCap (High Performance Capture) that started in January 2014. The HiPerCap project aims to develop novel post-combustion CO2 capture technologies and processes which are environmentally benign and have high potential to lead to breakthroughs in energy consumption and overall cost, involving all main separation technologies for post-combustion CO2 capture. The present contribution focuses on adsorption with low temperature solid sorbents as a promising technology to capture CO2 from the flue gas. More precisely, CSIRO and CSIC have developed CO2 adsorbents from different carbon precursors including petroleum pitch, phenolic resin and agricultural by-products. The performance of new materials can be evaluated either experimentally or by means of numerical simulations, but each methodology has drawbacks. Thus, it is of utmost importance to seek a simple method for evaluating and comparing materials on the basis of readily available adsorption data. It is well known that the ideal adsorbent has a high selectivity, a high working capacity, and a low adsorption enthalpy; however, in practice, it is very rare to find a material which combines all of these attributes. Therefore, the selection of the adsorbent will often involve a trade-off among these factors, making comparisons of varied adsorbents even more difficult. In this work, the potential of the activated carbons developed by INCAR-CSIC and CSIRO for a post-combustion CO2 capture process has been evaluated and compared by means of an adsorption performance indicator. ; This work has received funding from the HiPerCap Project of the European Union 7th Framework Programme FP7 (2007-2013; Grant Agreement number: 608555). N.A-G. also acknowledges a fellowship awarded by the Spanish MINECO (FPI program), and co-financed by the European Social Fund. ; Peer reviewed

The adsorption behavior of humid mixtures that are representative of postcombustion conditions on a microporous biochar was evaluated. The adsorption isotherms of H2O(v) were measured at 30, 50, and 70 °C up to the saturation pressure and fitted to the extended Cooperative Multimolecular Sorption (CMMS) model. Dynamic experiments were carried out in a fixed-bed adsorption unit with mixtures of N2, CO2, and H2O(v). Experimental results indicate that H2O is little affected by CO2 adsorption. On the other hand, the CO2 adsorption capacity can be reduced by the adsorption of H2O. The extent of this reduction is dependent on the amount of H2O adsorbed, which, in turn, is strongly dependent on the relative humidity of the gas phase and the adsorption time. A dynamic fixed-bed adsorption model that makes use of Ideal Adsorbed Solution (IAS) theory has been shown to be adequate to describe the adsorption behavior of CO2 from the ternary mixtures in the full range of conditions evaluated. ; Work carried out with financial support from the HiPerCap Project of the European Union 7th Framework Programme (FP7) (2007-2013; Grant Agreement No. 60855). ; Peer reviewed

The influence of N2 on CO2 adsorption was evaluated using a microporous biochar with a narrow pore size distribution. The adsorption isotherms of pure CO2 and N2 were measured at 0, 30, 50, and 70 °C up to 120 kPa and fitted to the Toth adsorption model. Dynamic breakthrough experiments were carried out in a fixed-bed adsorption unit using binary mixtures with compositions representative of different postcombustion streams (8–30% CO2) from ambient temperature to 70 °C. Dynamic adsorption experiments were simulated to validate the mathematical model of the adsorption process, as a necessary step for its later use for process design. The Ideal Adsorption Solution (IAS) theory, based on the pure component adsorption models, was used to account for competitive adsorption with satisfactory results. The information gathered in the present work will be used to extend the validity of the model to the adsorption of postcombustion streams containing H2O in part 2. ; Work was carried out with financial support from the HiPerCap Project of the European Union 7th Framework Programme FP7 (2007-2013; Grant Agreement number: 60855). M.G.P. acknowledges funding from the CSIC (JAE-Doc program cofinanced by the European Social Fund). N.Q. acknowledges funding from the Government of the Principado de Asturias (Severo Ochoa Program). The authors also appreciate the support from the technical consultants of AspenTechnology Inc., M.M. and E.L. ; Peer reviewed

12th International Conference on Greenhouse Gas Control Technologies, GHGT-12 ; High-purity H2 was produced by the sorption enhanced steam reforming (SESR) of acetic acid, a model compound of bio-oil obtained from biomass fast pyrolysis. A fixed bed reactor comprising two sections with different temperature was used to favor the reforming reaction in the high-temperature section, and the water gas shift (WGS) and the CO2 capture reactions along the low-temperature segment. A Pd/Ni-Co hydrotalcite-like material (HT) was used as catalyst and a CaO-based material as CO2 sorbent. High H2 yield (84.4%), with H2 purity of 99.8%, was obtained at atmospheric pressure and 600 °C in the above section of the bed followed by a bed temperature of 500 °C at the bottom part. A null CO concentration was achieved, while the CH4 and CO2 contents showed very low values (0.15% and 0.02%, respectively). ; The authors thank Franefoss Miljøkalk A/S (Norway) for supplying Arctic dolomite. G. Esteban-Díez acknowledges funding from the Government of the Principado de Asturias (Severo Ochoa program). ; Peer reviewed

13th International Conference on Greenhouse Gas Control Technologies, GHGT-13, 14-18 November 2016, Lausanne, Switzerland ; The development of adsorption-based technologies for post-combustion CO2 capture requires finding an adsorbent with adequate equilibrium and transport properties. Structured adsorbents are appealing for fixed-bed TSA processes, because they present lower pressure drop and higher thermal conductivity than conventional adsorbent beds, which facilitates the use of higher flowrates and shorter cycle times, maximizing throughput. In this work, the equilibrium of adsorption of the main flue gas components, CO2, N2, O2 and H2O over two carbon honeycomb monoliths with different textural development has been measured in a pressure and temperature range of interest for post-combustion CO2 capture: between 0 °C and 70 °C and up to 120 kPa for CO2, N2, and O2, and between 30 °C and 70 °C up to the corresponding saturation pressure for H2O. The maximum adsorption capacity and isosteric heat of adsorption follows the order: H2O > CO2 > N2 ≈ O2. The carbon monoliths present equilibrium selectivity towards CO2 and H2O over N2 and O2 at typical flue gas conditions. Moderate activation is preferred to maximize the CO2 adsorption capacity and selectivity in these conditions. The Toth model was employed to fit the equilibrium data for the adsorption of CO2, N2, and O2 with highly satisfactory results. The adsorption isotherms of H2O presents the characteristic "s" shape of hydrophobic adsorbents, with low uptakes at low relative pressures, which will facilitate H2O desorption during cyclic operation. These were fitted using the extended CMMS model, which describes satisfactorily the experimental data in the full relative humidity range. The adsorption kinetics were preliminary evaluated by measuring the rate of mass uptake from a mixture with 10% CO2 (balance N2) at 30 °C, 50 °C and 70 °C, and the data were fitted to the linear driving force model to obtain the kinetic rate constants. ; Work carried out with financial support from the HiPerCap Project of the European Union 7th Framework Programme FP7 (2007-2013; Grant Agreement number: 60855). N.Q. acknowledges a fellowship from the Gobierno del Principado de Asturias (Programa Severo Ochoa). ; Peer reviewed

Woody biomass pellets' demand for primary energy production is increasing. To guarantee sustainable and cost-efficient pellet production the diversification of biomass feedstock is mandatory. In this work it is proposed to re-use the solid biochar obtained from pyrolysis of eucalyptus (PEc) at 700 °C as an additive to produce enhanced pine sawdust (PIN) pellets. The process required the addition of glycerol as a lubricant in a percentage of 1 and 2 wt% per 5 and 10 wt% of pyrolyzed eucalyptus in the blend, respectively. Small additions of PEc enhanced PIN pellets' grindability and water-resistance, providing products with remarkable values of durability (up to 99%), net calorific value (up to 20 MJ/kg), energy density (up to 13.3 GJ/m3), and particle density (up to 1.24 g/cm3). N, S, chlorine, and heavy metals contents were also analyzed. The proposed pellets fulfill the A1/A2 and the I1/I2 quality classes for domestic and industrial wood pellets, respectively. A preliminary economic evaluation indicated that pellets made up from a mixture of 90% PIN and 10% PEc are competitive compared to raw PIN pellets, with expected savings in the costs of production, energy, transport, and construction of a storage site of 4, 13, 10 and 7%, respectively. ; This work was carried out with financial support from the Gobierno del Principado de Asturias (PCTI, Ref. IDI/2018/000115), co-financed by the European Regional Development Fund (ERDF). M.V. Gil acknowledges support from a Ramón y Cajal grant (RYC-2017-21937) of the Spanish Government and the Spanish State Research Agency, co-financed by the European Social Fund (ESF). ; Peer reviewed

Energy generation from non-hazardous waste streams, which are unfeasible to be reused or recycled, can help overcome some of the problems related to fossil fuel depletion, global increase in energy demand and waste generation management under restricted landfilling. One of the main drawbacks of waste-to-energy strategies is the poor combustion properties of waste, which densification could help to circumvent. This work studies the co-pelletization of refused derived fuel (RDF) and pine sawdust (PIN) in a continuous pilot pellet mill that resembles industrial pelletization. The effect of RDF contents up to 90 wt% on a set of parameters has been assessed: pelletization energy consumption, physical properties (durability, particle and bulk densities), net calorific value and energy density of the obtained pellets. In addition, slagging, fouling and corrosion, phenomena associated with combustion, were estimated from the ash composition. Results showed that obtaining pellets with a low RDF loading (2–9 wt%) was feasible. They accomplished ISO 17225-2 solid biofuels standard for industrial use, and presented low deposition and corrosion risks. On the other hand, pellets with 30–90 wt% RDF were also manufactured and complied with the UNE-EN 15359:2012 solid recovered-fuel standard for energy recovery in incineration and co-incineration plants. All the produced pellets presented durability and net calorific value above 96.9% and 10.7 MJ/kg, respectively. Energy density higher than 10.6 GJ/m3 was obtained for pellet formulations with RDF content up to 50 wt%. It was demonstrated that the blends of RDF and PIN can provide high-quality pellets with a high load of waste material, under the same operational conditions required for PIN pelletization. It is a versatile process that can be tailored to different product requirements depending on the end-use. It promotes energy recovery and generates value out of a waste fraction with no relevant use, adding economic and environmental benefits. ; This work was carried out with financial support from the Gobierno del Principado de Asturias (PCTI, Ref. IDI/2018/000115), co-financed by the European Regional Development Fund (ERDF) and from the CSIC (Project PIE, Ref. 202080E115). M.V. Gil acknowledges support from a Ramon y Cajal grant (RYC-2017-21937) of the Spanish Government and the Spanish State Research Agency, co-financed by the European Social Fund (ESF). ; Peer reviewed

This paper presents an experimental and numerical study on co-firing olive waste (0, 10%, 20% on mass basis) with two coals in an entrained flow reactor under three oxy-fuel conditions (21%O2/79%CO2, 30%O2/70%CO2 and 35%O2/65%CO2) and air–fuel condition. Co-firing biomass with coal was found to have favourable synergy effects in all the cases: it significantly improves the burnout and remarkably lowers NOx emissions. The reduced peak temperatures during co-firing can also help to mitigate deposition formation in real furnaces. Co-firing CO2-neutral biomass with coals under oxy-fuel conditions can achieve a below-zero CO2 emission if the released CO2 is captured and sequestered. The model-predicted burnout and gaseous emissions were compared against the experimental results. A very good agreement was observed, the differences in a range of ± 5–10% of the experimental values, which indicates the model can be used to aid in design and optimization of large-scale biomass co-firing under oxy-fuel conditions. ; L.A. acknowledges funding from the CSIC JAE program, co-financed by the European Social Fund. J.R. acknowledges funding from the Government of the Principado de Asturias (Severo Ochoa program). Financial support from the CSIC (Project PIE 201080E09) is gratefully acknowledged. ; Peer reviewed

The deployment of oxy-fuel combustion in utility boilers is one of the major options for CO2 capture. However, combustion under oxy-firing conditions differs from conventional air-firing combustion, e.g., in the aspect of radiative heat transfer, coal conversion and pollutants formation. In this work, a numerical study on pulverised coal combustion was conducted to verify the applicability and accuracy of several sub-models refined for oxy-fuel conditions, e.g., gaseous radiative property model, gas-phase combustion mechanism and heterogeneous char reaction model. The sub-models were implemented in CFD (Computational Fluid Dynamics) simulations of combustion of three coals under air-firing and various oxy-firing (21–35% vol O2 in O2/CO2 mixture) conditions in an EFR (entrained flow reactor). The predicted coal burnouts and gaseous emissions were compared against experimental results. A good agreement between the simulations and experiments was achieved, indicating a good applicability and reliability of the refined sub-models and suitability of use of the experimentally derived kinetic data in coal devolatilisation and char oxidation sub-models. The sub-models and the practices implemented in this work can be used in large-scale oxy-fuel combustion processes for reliable design and optimization. ; L.A. acknowledges funding from the CSIC JAE program, which was co-financed by the European Social Fund. J.R. acknowledges funding from the Government of the Principado de Asturias (Severo Ochoa Program). Financial support from the CSIC (Project PIE201080E09) is gratefully acknowledged ; Peer reviewed

The HiPerCap (High Performance Capture) project started 1st January 2014 as a part of the 7th framework program of the European Commission. HiPerCap aims to develop novel post-combustion CO2 capture technologies and processes which are environmentally benign and have high potential to lead to breakthroughs in energy consumption and overall cost. The project will study process concepts based on absorption, adsorption and membranes. These process concepts will be assessed using a novel methodology for benchmarking with new and emerging technologies, for which limited data are available and the maturity level varies substantially. Based on the assessment, two breakthrough technologies will be selected for more thorough benchmarking against demonstrated state-of-the-art technologies. This paper presents the objectives of the project, expected outcomes, and the results obtained within the first eight months period. ; The project receives funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement n° 608555. We gratefully acknowledge the industrial partners who also financially support the project. ; Peer reviewed

The effect of co-firing coal and biomass on the ignition behaviour and NO emissions was evaluated under both air and O2/CO2 (21-35% O2) atmospheres. The results showed a worsening of the ignition properties in the 21%O2/79%CO2 atmosphere in comparison with air. Furthermore, in order to obtain similar or better ignition properties, the oxygen concentration in the O2/CO2 mixture must be 30% or higher. A decrease of the ignition temperature was observed with the addition of biomass in air and oxy-fuel conditions. The results also indicate that NO emissions in the 21%O2/79%CO2 atmosphere were lower than under air-firing conditions, although they increased in the 30%O2/70%CO2 and 35%O2/65%CO2 atmospheres. The addition of biomass resulted in lower NO emissions in all cases. ; This work was carried out with financial support from the Spanish MICINN (Project PS-120000-2005-2) co-financed by the European Regional Development Fund. L.A. and M.V.G. acknowledge funding from the CSIC JAE program, co-financed by the European Social Fund. J.R. acknowledges funding from the Government of the Principado de Asturias (Severo Ochoa program) ; Peer reviewed